yle="font-size: 23px; line-height: 1.3em; color: rgb(0, 0, 0);font-family:sans-serif,Verdana;">
- High-torque, quiet-running and well balance.
- Ideal for precision grinding and finishing works.
- Replaceable collet chuck:Ø3.0mm is standard, the Ø2.34 and Ø3.175mm collet are optional
Air Pressure | Weight | Dimension |
---|
90psi (6.2kg/cm2 ) | 110g | Ø20x160L (mm) |
General assembly
In order to achieve the best state of pneumatic tools and extend its life, need to connect three points in combination to achieve the ability to filter out water vapor, control intake pressure and lubrication.
Handpiece Three point combination ompressor
(Filter· Regulator· Lubricator)
Improve the use of performance and life requirements:
In order to achieve the best state of pneumatic tools and extend its life, need to connect three points in combination to achieve the ability to filter out water vapor, control intake pressure and lubrication.
l Before using the pneumatic tool, be sure to check that there is enough oil in the oil pan within the three-point combination.
l The three-point combination of inlet pressure at 90 psi (6.2 kg / cm 2 ) is the most suitable condition for use.
l Before use, please check whether the three-point combination of the water bottle is full, if the first full of water will be discharged.
l Adjust the three-point combination of oil intake, it is recommended about 2CC per minute (often used).
l If you encounter a holiday or do not use pneumatic tools for a long time, in the first opening, please raise the combination of three points into the oil per minute 4CC, while opening the pneumatic tools to low speed idling 20-30 seconds, so that the oil is indeed After lubrication of each part, and then adjust to the normal speed of use is better.
l Selection of lubricants: Do not use too thick lubricants, it is recommended to use the circulating oil R32.
Operation, start / stop setting:
§ ON / OFF switch is operated in a rotating manner. When the switch valve body is facing the user, turn it counterclockwise and turn it clockwise (OFF).
※ Before using the pneumatic tool, make sure that the switch is in "OFF" status.
§ When you turn on the pneumatic tool switch, please turn 90 °, so that you can reach the maximum speed, if the rotation angle is too large, not only no effect and will cause the switch valve off damage.
protective device
Please wear any protective equipment such as ear protectors, goggles, safety aprons, helmets, gloves and so on.
Pneumatic tools after use
The tool must be kept in a clean, dry place, and it is recommended to store at constant temperature, to avoid the sudden change in temperature environment. Do not drop the pneumatic tool when the pneumatic tool is not completely stopped during operation.
Detailed safety rules and reminders
When using pneumatic tools, safety is the main consideration. The pneumatic tool must be operated in a safe condition. Please read the following provisions before use and use the pneumatic tool safely.
§ This pneumatic tool is designed for grinding or engraving and fine polishing and other industrial applications, do not use the body!
§ Check the air pressure before operation, the pressure below 90psi (6.2kg / cm 2 ) will reduce the speed and strength, but higher than 90psi will lead to speeding operation , which is verydangerous , and will shorten the life of the tool!
§ Please use good quality abrasive supplies, please do not use damaged materials with poor quality or poor quality.
§ If the noise figure exceeds 85 dB (A) during operation, the operator must wear earplugs or ear protectors.
§ The use of the operator for a long time may cause injury due to vibration, especially the palm and arm. Work damage caused by vibration depends on many factors, such as the type of consumables used, the process, the user\`s physical condition, working environment, working hours, temperature, and so on. So the operator must use pneumatic tools in accordance with ISO5349 provisions of the construction.
§ When used, pay attention to hair, loose clothes or tie to avoid being involved in pneumatic tools.
§ The working area should be well ventilated, preferably with a dust collector, to avoid inhalation of dust or gas discharged from the air compressor.
§ If any lubricant stains eyes or accidentally ingestion please seek medical treatment immediately.
§ Do not modify or remove pneumatic tools without the permission or consent of the manufacturer.
§ While the pneumatic tool is running, be sure not to touch the supplies in rotation.
§ Make sure to use the sparks that are produced without hurting people around them or splashing them into flammable substances.
§ Make sure that the workpiece is already supported or fixed to avoid flying out of the workpiece.
§ Do not use air ducts other than standard equipment, and do not pull the ducts when you use them.
Recommended clamping length and safety requirements for revolutions and extension length
Note: Clamping length L should not be less than 10mm
Recommended supplies extended length H (mm)
·L = clamping length
·H = extended length of consumables
·T = abrasive length
·ØD = grinding rod diameter