|
aHR0cDovL2ZyZWVzaGlwLmNvLmty
- ¸ÂÃã °¡´É À¯¹«: YES
- ÆÐÅÏ Á¾·ù: °¡¹æ ¹× »óÀÚ
- ±Ù¿ø: CN (Á¤Ç°)
STEP 1 // Run the `Main Box Side` die through your die-cutting machine and cut 4 times, this will form the sides of your box.
STEP 2 // Run the `Main Box Lid` die through your die-cutting machine, this will create the lid for your box.
STEP 3 // Fold and burnish all of your score lines.
STEP 4 // Use a strong adhesive or Red Liner Tape to assemble the lid of the box, as shown.
STEP 5 // You should now have four separate side panels, and one lid, as shown.
STEP 6 // To form the bases for this box, you will need to cut your cardstock to the following sizes: Base for Outer Layer- 3.8"x 3.8" (9.6cm x 9.6cm) Bases for three inner layers ( starting with the largest and gradually getting smaller): First Layer Base- 3.5"x 3.5" (8.9cm X 8.9cm) Second Layer Base - 3.2"x 3.2"(8.1cm x 8.1cm) Third Layer Base- 3.0" x 3.0" (7.6cm x 7.6cm) Cut out 4 squares of each size, one for each side of your box.
STEP 7 // To form the side panels for this box, you will need to cut your cardstock to the following sizes: First Layer Side- 3.5"x 4.0" (8.8cm x 10.1cm) Second Layer Side- 3.2" x 4.0" (8.1cm x 10.1cm) Third Layer Side - 3.0" X 4.0" (7.6cm x 10.cm) Cut out 4 panels of each size, one for each side of your box.
STEP 8 // Line up each of the corresponding dies on one end of the panel, this will give you the flap and fold you need to adhere to the bases you previously cut in Step 6.
STEP 9 // Using your `Main Box Side` die-cut,adhere to the `Outer Layer Base` along the long edge (see picture).
STEP 10 // Rotate your base 90° and repeat for each of the box sides. Your box should look like the image shown here.
STEP 11 // Adhere your die-cut `First Layer Side`to `First Layer Base` along the flap.
STEP 12 // Rotate 90° and repeat for all 4 sides. You should have the results shown here. Repeat for all "base` sizes & layers`.
STEP 13 // Apply adhesive to the underside of each of the `Base` pieces, and layer them inside each other, in descending size order, as shown here.
YOU CAN ADD DIMENSION TO THE SIDE PANELS YOU CREATED IN STEP 7 BY ADDING LAYERS USING THE FOLLOWING MEASUREMENTS: 1ST LAYER SIDE: 3.5" x 4.0" (8.8cm x 10.1cm) [LAYER 1: 3.2" X 3.4" (8.1cm X 8.6cm) LAYER 2: 2.9" x 3.0" (7.3cm x 7.6cm) 2ND L AYER SIDE: 3.2" x 4.0" (8.1cm x 10.1cm) LAYER 1: 3.0" x 3.4" (7.3cm x 8.6cm) LAYER 2: 2.6"x 3.0" (6.6cm x 7.3cm) 3RD LAYER SIDE: 3.0" X 4.0" (7.6cm x 10.2cm) LAYER 1: 2.7" x 3.4" (6.8cm x 8.6cm) LAYER 2: 2.4" x 3.0" (6.1cm x 7.6cm) REPEAT 4 TIMES, ONE FOR EACH SIDE. STEP 14 //To assemble the Exploding Box, fold all of the side panels upwards, as shown here,and place the lid on the top to finish.
ADD RIBBON OR A ROSETTE TO THE LID OF THE BOX FOR A FINAL FLOURISH!
Specifications:
Condition: 100% Brand New
Color:Silver
Material: Carbon Steel
Size:(Approx): As the picture show
Conversion: 1cm=0.39inch /1 inch =2.54cm
Package included :
1 X Cutting Dies
Applicable models:
They work with virtually any die-cutting machine ,will accommodate wafer-thin dies and are sure tobecomeanessential ingredient in your paper crafting process.
What to cut:
These steel dies can cut card paper, thin chipboard, 1/4 inch cork, acetate, sandpaper, 2mm craft foam, wood veneer paper, photo magnet sheets and much more!
Tip:
when using a more complex mold, please pad an extra sheet of paper, and the rolling times need to be increased accordingly
Notice:
1.Due To The Light And Screen Difference, The Item`s Color May Be Slightly Different From The Pictures.
2.Please Allow 1-3cm Differences Due To Manual Measurement.
3.Thank you very much for your support and understanding
|
|
|
|
|