|
aHR0cDovL2ZyZWVzaGlwLmNvLmty
- ÀÎÅÍÆäÀ̽º Á÷°æ: ¾Æ¹«µµ
- ¼öÁú ¿ä°Ç: »ó¼öµµ/ÁöÇϼö
- 5´Ü°è ¿©°ú: ¾Æ´Ï´Ù
- ½ÃÀå Ãâ½Ã ½Ã°£: 2009
- ÀÓ¸í: Vertical
- ±â´É: °£Á¢ À½¿ë
- Àü·Â(W): 45W
- ¸ðµ¨ ¹øÈ£: PL-5QRAO
- Àç·á: ½ºÅ×Àη¹½º ½ºÆ¿
- Á¤¼ö À§Ä¡: Áß¾Ó Á¤È½Ä
- À¯Çü: ¿ÀÁ¸ Á¤¼ö±â
- ¹° ó¸® ±â°è À¯Çü: ¹° Á¤È±â
- »ç¿ë: °¡Á¤¿ë »çÀü¿©°ú
- ºê·£µå À̸§: Pinus longaeva
- ¿ø»êÁö: Áß±¹
- CN: Guangdong
- Product name: Quartz tube type ozone generator Kit
- Cooling way: Air cooling
- Gas source: Air source, oxygen source
- Maximum air pressure: <0.2Mpa (200kpa)
- Working air pressure: <0.07Mpa (70kpa)
- Environment: <40 degrees Celsius, <85%RH
- Temperature rise: <8 degrees Celsius
- Heat dissipation effect: Increase 1.6 times
- Ozone concentration: Increase 10%-15%
- Product application: Air purification and water sterilization
- Service life / Warranty: More than 20000 hours / 2 years
- Customized: Can be customized
¿É¼ÇÁ¤º¸[(29)5G]
Product picture:
(When the product works, there is no electricity on the red radiator, which is very safe)
There is no need to distinguish between inlet and outlet.
Inlet: We recommend that you use 4*7mm silicone tube or 5*8mm PU tube.
Outlet: We recommend that you use 6*8mm Teflon tube.
If you need to change the connector, please contact us.
Product parameters:
Product introduction:
Product name: Quartz tube type ozone generator Kit
Cooling way: Air cooling
Gas source: Air source, oxygen source
Gas pressure: <0.2Mpa (200kpa)
Environment: <40 degrees Celsius, <85%RH
Temperature rise: <8 degrees Celsius
Heat dissipation effect: Increase 1.6 times
Ozone concentration: Increase 10%-15%
Inner electrode: 316L stainless steel tube
Product application: Air purification and water sterilization
Service life / Warranty: More than 20000 hours / 2 years
Customized: Can be customized
Low temperature rise, high efficiency, moisture-proof, low-voltage protection, over-voltage protection, over-current protection, over-heat protection, open-circuit protection, short-circuit protection, automatically stabilize the output power.
Installation requirements:
We recommend that you install the ozone tube on the insulating board. If you want to install it on a metal shell, we recommend that you connect a ground wire to your metal shell.
You can use long screws to install the ozone PSU (ozone power supply, circuit board) away from the ozone tube (metal shell or other electrical appliances) more than 4cm. (Front, back, left, right, up, down)
When you get our product, you will get installation and operation instructions, which is simple.
|
|
|
|
|